|Listing Format:||Fixed Price|
|Price per item:||Buy Now for $13,000.00|
|Closes:||12 Days, 17 Hours|
|Location:||Kansas, United States|
|Started :||4/7/2017 2:41:28 PM|
|Ends:||5/7/2017 2:41:28 PM|
View this user's other listings
Ask the listing owner a question
Mail this listing to a friend!
Watch this item!
RC Components Front and Rear Wheel. Rear is 10" Wide, Side Drive Beadlock. Rear tire that I am using is the Mickey Thompson 10.5 X 28-15. World Wide Bearing Ceramic Bearings in Both Front and Rear Wheels. Outboard Bearing Support is a ceramic ball bearing also but was purchased at a local auto parts store. This Chassis is wide enough to handle a 12" rear wheel. Pictrues in this posting is featuring a 12" Hawaya Racing Products wheel. The wheel does not go with the chassis when purchased but will sell it the purchaser wants to buy the wheel. Also, the brakes will be the Koenig Engineering 10" disk brake rotors front and rear. The 11.5 PMFR Floating disk will not be included in the sale either.
PMFR Hollow Rear Axle.
Koenig Engineering 4" over axle blocks.
Kenny's Composites Carbon Fiber Wheel Tub.
3 1/2 Inch offset sprocket
Koenig Engineering Backbone Update. I took the chassis to Jim at Koenig Engineering and the backbone was taken apart and refitted with (2) new Chrome Mony tubes to accomodate the taller Billet Cylinder Block, due to running a stroker crankshaft also heighth being affected by running Vortex 2 Cylinder Head also. You can determine the refitted tubes in some of the pictures due to the non powder coated tubes. Cost to do this alone was $1,500.
Koenig Engineering Fuel Tank Update. (2) Fuel Bungs added instead of one. One is designated for the engine and the other is designated for the Nitrous System. (2) Pingle Fuel Valves. Recirculating Fuel System with the Holley Fuel Pressure Regualtor. Fuel Line used in the Fuel System is the Aeroquip Fuel Line with -6an Summit Racing fittings.
RPM Computer: (4) EGT Sensors, (4) O2 Sensors, Clutch Sensor, Output Shaft Sensor, Nitrous Pressure Sensor, Fuel Pressure Sensor, and Battery Voltage.
New in 2016: Murray Big Tube Pipe, Dyno Tune Digital Nitrous Pressure Gauge.
New in August or later of 2016: (2) Nitrous Express Nitrous Solenoids, (one solenoid is used as a safety and the other is used as the control solenoid), Nitrous Express Fuel Solenoid, Holley Blue Fuel Pump, Wiring Updated using Deutsch Connectors. Complete wiring was done Professionally by Kevin in Topeka, Ks. Kevin wires Drag Cars, Street Rods and an occasional dragbike in and around the Topeka area.
Schnitz Pro Series II Ignition Controller on the bike. I also have a brand New Pro Series II box as aa backup box that will be sold separately that was purchased new in 2015. The box has only been installed one time to trouble shoot wiring issues on the bike in August of 2016, otherwise the box was taken back off of the motorcycle and put back in the box it came in. All of the wiring goodies, (Wiring, Terminal Ends, Spark Plug Wires, Arming Switch), that come with the purchase of a new Schnitz box are still in its original box, nothing has been robbed out of it. Purchaser of the chassis has first chance to buy the backup box if he or she chooses to do so.
(4) Dyna Coils. This set up is used for dual plug head.
(2) Max Amp Batteries and Charger. These Trick Batteries weigh in at 2 lbs.. The cost to purchase these batteries and charger new was $730.00.
This Chassis is ready to go. It is not a want to be. Its all here. All you need to have in the motor. The Best 1/4 Mile ET and Best 1/4 Mile MPH is 6.889 @ 191.27 MPH. The Best 1/8 Mile ET is 4.385 and the best 1/4 Mile MPH is 166.23 MPH. If you would like, I can provide more pictures as well as video. If you have any questions give me a call. Thanks for your interest.
Will consider reasonable offers...